ARZENTIQ
CONSTRUCTION

Construction utilities

Areas, quantities, and layouts for building, garden and farm work: concrete, aggregate, lumber, masonry, tile, paint, grain bins, sprayers, yields.

Quantity take-offs for building, garden and farm work: how much concrete, aggregate, lumber, brick, tile, roofing, paint, or drywall a job needs, from the dimensions you measure — and in the field, what a grain bin holds, how a sprayer is calibrated, what a crop is likely to yield and how much hay a herd needs. Waste allowances and rates are yours to set, product figures are quoted from the manufacturer’s own documents, and nothing here is a structural, code or agronomic recommendation — the pages say so.

Construction utilities

59 utilities

Concrete & aggregate7

  • Estimate

    Aggregate & Asphalt Tonnage

    Gravel, sand, crushed stone, or asphalt from area and depth: cubic yards or metres, then tons and tonnes from the density your supplier quotes.

    You get: The volume and the tonnage to order, in short tons and metric tonnes side by side, from a density you can point to — yours or a cited reference.

    Open Aggregate & Asphalt Tonnage
  • Calculate

    Concrete Footing & Pier Volume

    Concrete for strip or pad footings and round or square piers (with an optional bell), a waste allowance, and bags from the yield printed on your bag.

    You get: Volume per footing and per pier, the total in yd³ or m³ with waste, and a bag count from the yield you enter — with the formulas and the equivalent-shaft note for a bell under a square pier.

    Open Concrete Footing & Pier Volume
  • Calculate

    Concrete Mix Ratio

    Split a concrete volume into cement, sand and aggregate by a volume ratio (1:2:4 …) with your dry-volume factor, bulk densities, bag size and w/c ratio.

    You get: Loose volume of each material, masses and cement bags from the densities you enter, water from the w/c ratio — every factor yours, and the batching caveat stated.

    Open Concrete Mix Ratio
  • Calculate

    Concrete Stairs Volume

    Concrete for a straight flight, solid on grade or on a waist slab, from width, riser, tread and step count, plus a landing, waste and bags; formwork area too.

    You get: Steps, waist and landing volumes, the total with waste in yd³ or m³, bags from your yield, and the riser and stringer formwork area — geometry stated, stair limits not judged.

    Open Concrete Stairs Volume
  • Estimate

    Concrete Volume & Bags

    Concrete volume for a slab or a round hole, a waste allowance, and the bag count from a manufacturer-stated yield or your own — with the rounding shown.

    You get: Cubic metres or yards to order, or how many bags to buy and how much is left over, traceable to your dimensions, waste figure, and the yield you chose.

    Open Concrete Volume & Bags
  • Estimate

    Gravel Driveway Depth & Tonnes

    Gravel or crushed stone for a driveway by layer — sub-base, base, surface — from your depth, density and allowance: volume, tonnes, cost and truck loads.

    You get: Per-layer and total volume (bank and loose), tonnes and short tons, cubic yards, cost at your price per tonne, truck loads for your capacity, and a CSV of the layers.

    Open Gravel Driveway Depth & Tonnes
  • Estimate

    Rebar Calculator

    Bars each way for a slab or footing from its size, spacing and cover; total length, laps at your stock length and weight from nominal bar mass. No design rules.

    You get: How many bars run each way, their lengths, the splices a stock length forces, the lap length you specify, and the weight and cost from labelled nominal kg/m for the bar size.

    Open Rebar Calculator

Areas & layout7

  • Calculate

    Pool, Tank & Aquarium Volume

    Volume of a rectangular, round, oval or kidney pool or an upright tank, with shallow and deep ends, in litres, m³, US and UK gallons; fill time at your flow.

    You get: The volume of a pool or tank in every unit with exact conversion factors, the average depth used, the mass of water, and how long a hose or pump takes to fill it at the rate you enter.

    Open Pool, Tank & Aquarium Volume
  • Calculate

    Roof Pitch, Rafter & Area

    Pitch as rise-per-12, degrees, or percent; rafter length from span and overhang; sloped roof area, squares, and shingle bundles at your count per square.

    You get: The roof figures a gable job needs: the pitch in every form, the rafter line length, the actual sloped area, and how many squares or bundles to order.

    Open Roof Pitch, Rafter & Area
  • Estimate

    Sod & Turf Calculator

    Rolls or slabs of turf for a lawn from one or more shapes, the roll size your supplier sells and the waste you allow; pallets and cost from your figures.

    You get: Lawn area from rectangles, circles, triangles or a known figure, the rolls needed after your waste allowance, and pallets or cost at the supplier's numbers you enter.

    Open Sod & Turf Calculator
  • Calculate

    Square Footage & Area

    Area of a room, floor, or surface built from rectangles, triangles, circles, and trapezoids — openings subtracted — in square feet, yards, and metres at once.

    You get: The area of an irregular space, section by section so it can be checked, with a waste allowance and a cost at your price per square foot or metre, exportable as CSV.

    Open Square Footage & Area
  • Calculate

    Stair Rise, Run & Stringer

    Number of risers, riser height, tread depth, total run, stringer length, and angle for a straight flight — checked only against the limits you enter.

    You get: A stair layout from the floor-to-floor height: how many steps, how tall and deep each is, how far the flight runs, and how long to cut the stringers.

    Open Stair Rise, Run & Stringer
  • Estimate

    Tile & Flooring Quantity

    How many tiles or planks an area needs from the tile size and grout joint, with your waste allowance, boxes by count or coverage, and the spare after rounding.

    You get: A tile or plank count and box order for a floor or wall — with the joint accounted for, the rounding visible, and the cost at your price per box.

    Open Tile & Flooring Quantity
  • Calculate

    Wall Area with Openings

    Net wall area for painting or papering: rooms with length, width and height, openings by room with counts, optional ceilings, and quantity from your coverage.

    You get: Gross wall area, openings, net area per room and in total, ceiling area, the waste-adjusted total, and the product quantity from your coverage and number of coats.

    Open Wall Area with Openings

Lumber & masonry13

  • Calculate

    Baluster Spacing Calculator

    Even baluster spacing between posts: fewest balusters for the maximum gap you enter, exact gap and on-centre distance, layout marks, totals with waste.

    You get: Baluster count, clear gap, centre-to-centre spacing, the position of every baluster from the post, and totals over several sections with waste — the gap limit is yours.

    Open Baluster Spacing Calculator
  • Calculate

    Block Wall (CMU) Calculator

    Concrete blocks for walls less openings from your nominal block size, with courses per wall, waste, mortar bags from the product yield and grout for cells.

    You get: The block count to order and the mortar and grout to go with it, with the course and per-course arithmetic shown so the wall height and length can be checked against the block module.

    Open Block Wall (CMU) Calculator
  • Calculate

    Board Foot & Lumber

    Board feet for a lumber list from nominal sizes, each item’s dressed (actual) size from the American Softwood Lumber Standard, linear feet, and cost.

    You get: A priced lumber tally you can hand to a yard — board feet per item and in total, the actual dressed dimensions, and the dressed volume kept separate from the nominal count.

    Open Board Foot & Lumber
  • Estimate

    Brick, Block & Mortar

    Bricks or blocks for a wall from the unit size and joint, openings taken out, your waste allowance, mortar volume from the joint geometry, and bags.

    You get: A unit count, pack count, and mortar quantity for a single-leaf wall that you can trace to the unit size, joint width, and area you entered.

    Open Brick, Block & Mortar
  • Estimate

    Deck Calculator

    Deck boards, joists and screws from the deck size, actual board width, your gap and joist spacing, stock length and waste — geometry only, not a span table.

    You get: The number of boards (and boards per row when stock is short), joists at your spacing, screws at two per crossing, linear footage and an optional board cost.

    Open Deck Calculator
  • Estimate

    Fence Calculator

    Posts, rails, pickets and concrete bags for a fence run from its length, your post spacing, gates and board size — layout arithmetic, no spacing rules assumed.

    You get: How many posts, rails and pickets a run needs, the equal spacing that fits, and the bags of concrete at the rate you enter — with every count shown as a formula.

    Open Fence Calculator
  • Calculate

    Mortar Mix Calculator

    Split a mortar volume into cement, lime and sand by your volume ratio (1:1:6, 1:4 …) with a dry-volume factor, waste, bulk densities and bag sizes.

    You get: Loose volume of each material, masses and bags from the densities you give — no mortar-type table embedded; the ratio and its permitted use come from your specification.

    Open Mortar Mix Calculator
  • Calculate

    Paver & Patio Calculator

    Pavers for a patio from its area and your paver size and joint, with waste, pallets, edge restraint, and base gravel, bedding and jointing sand at your depths.

    You get: The number of pavers to order and the gravel, sand and edging to go under and around them, from the paver module and the depths you specify rather than a fixed build-up.

    Open Paver & Patio Calculator
  • Calculate

    Pergola Post & Beam Calculator

    Posts, beams, rafters and purlins for a rectangular pergola from its size, spacings and overhang, with lengths, embedment and stock-length pieces to order.

    You get: Post count and actual spacing, beam and rafter lengths with overhang, purlin count, a linear take-off per member and the pieces of your stock length each needs.

    Open Pergola Post & Beam Calculator
  • Estimate

    Plywood & OSB Sheathing Calculator

    Sheets of plywood or OSB for walls, roofs and floors from areas typed one per line, less openings, in your sheet size with waste — plus cost and fasteners.

    You get: Gross and net area, exact and rounded-up sheet count with the waste allowance, leftover material, cost at your sheet price and fasteners per sheet and in total from the spacings you enter.

    Open Plywood & OSB Sheathing Calculator
  • Calculate

    Retaining Wall Block Calculator

    Blocks, caps, courses and gravel for a segmental retaining wall from your block size, buried course, waste allowance, base depth and drainage width.

    You get: Courses (with the overshoot when the height does not divide), blocks per course, block and cap counts with waste, base and drainage gravel volumes — counts only, engineering left to you.

    Open Retaining Wall Block Calculator
  • Estimate

    Skirting & Trim Length

    Skirting, cornice, chair rail or quarter-round for several rooms: perimeter minus openings, sticks of your stock length with or without offcut reuse, and cost.

    You get: Run per room and in total, sticks by first-fit layout or whole sticks per wall, the waste-adjusted figure, inside corner count, cost at your price, and a CSV per room.

    Open Skirting & Trim Length
  • Calculate

    Wall Framing Calculator

    Studs, plates, headers, jacks, cripples and sills for stick-framed walls from length, corners and openings at the spacing, stud size and plate count you set.

    You get: A per-wall take-off (common, corner, king, jack, cripple studs and sills), total studs with waste and their linear length, plate and header lengths — layout arithmetic only.

    Open Wall Framing Calculator

Finishes10

  • Estimate

    Carpet & Underlay

    Carpet from a roll: strips, seams and roll length for both orientations, the cheaper layout, waste, underlay from its own roll width, and gripper less doorways.

    You get: The best orientation with strips, strip length, roll length and seams, the carpet area and waste percentage, the underlay roll length, gripper length and costs from your prices.

    Open Carpet & Underlay
  • Estimate

    Ceiling Tile & Grid

    Suspended ceiling take-off: tiles with centred borders, main runners, cross tees, wall angle and hangers for a room and tile module, in your stock lengths.

    You get: Tiles (full, cut, with waste and boxes), border sizes at each wall, main runner count and stock pieces, cross tees, wall angle length and pieces, and hanger count.

    Open Ceiling Tile & Grid
  • Estimate

    Drywall Sheets & Compound

    Drywall or plasterboard sheets for an area from the sheet size, openings, and your waste; joint compound from a stated coverage, pails, and screws at your rate.

    You get: A board take-off you can order from — sheets, compound, pails, and screws — with every figure traceable to the sizes, coverage, and rates you entered.

    Open Drywall Sheets & Compound
  • Estimate

    Flooring Planks & Boxes

    Laminate, vinyl or engineered flooring: room area plus waste, boxes from the carton coverage, planks and rows from the plank size, and a last-row check.

    You get: Area to buy, boxes (rounded up) and their cost, planks per box and total planks, rows across the room, the last-row width and whether to split the first and last rows, and the leftover.

    Open Flooring Planks & Boxes
  • Estimate

    Grout & Thinset Quantity

    Grout mass and bags from the tile size, joint width and thickness with the density you enter, and thinset from the trowel notch and bed factor with its density.

    You get: Joint volume and grout mass with bags rounded up, thinset bed volume, mass and bags, the joint share of the floor, the tile count, and the waste allowance applied.

    Open Grout & Thinset Quantity
  • Calculate

    Miter & Compound Miter Angles

    Miter angle for any corner, compound miter and bevel for crown moulding laid flat from the corner and spring angle, and the cut angle for n-sided frames.

    You get: Saw settings from square for each piece (miter, and bevel for crown) with which end to keep, the cut angle from the edge, and for polygons the interior angle and number of cuts.

    Open Miter & Compound Miter Angles
  • Estimate

    Paint Coverage

    Litres or gallons for walls and ceilings from area, openings, coats, and a coverage you can name — manufacturer-stated or your own — with cans and spare.

    You get: How much paint to buy for a room and how many cans that is, traceable to the area you measured, the coats you chose, and the spreading rate on the product.

    Open Paint Coverage
  • Calculate

    Siding & Cladding Calculator

    Net siding area from walls and gables minus openings, with waste, pieces from the coverage of your board or panel, plus trim and corner post lengths.

    You get: Wall, gable, opening and net areas, the area with waste, a piece count from the coverage you enter, and linear totals for opening trim and corner posts.

    Open Siding & Cladding Calculator
  • Calculate

    Stucco & Plaster Calculator

    Stucco or plaster by coat: the volume of each coat at your thickness, the bags or the sand and cement it takes, plus lath sheets and corner bead.

    You get: Net area after openings, the volume and bag count of every coat at your thicknesses, the total with waste and what it costs, or sand and cement by your mix ratio, with lath sheets and bead sticks.

    Open Stucco & Plaster Calculator
  • Estimate

    Wallpaper Calculator

    Rolls of wallpaper by the drop method: wall height plus pattern repeat per drop, drops per roll from the label, drops from the perimeter — not area ÷ roll.

    You get: How many rolls to buy for a room, from your walls and the roll size and repeat printed on the label, with the drop count that explains it and the naive area figure for comparison.

    Open Wallpaper Calculator

Site & earthworks7

  • Calculate

    Acreage & Land Area Calculator

    Acres, hectares, m² and ft² of a parcel from a rectangle, a triangle by three sides, a circle, or corner coordinates of any polygon (shoelace), with perimeter.

    You get: The area of a lot or field in every unit a deed, a seed bag or a fencing quote uses — from the measurements you have, including an irregular boundary walked corner by corner.

    Open Acreage & Land Area Calculator
  • Calculate

    Cubic Yards & Volume Calculator

    Cubic yards, cubic feet and cubic metres for slabs, pads, beds and fills from length, width and depth, several shapes at once, with waste, tonnage and cost.

    You get: The volume to order for concrete, gravel, soil or mulch, in the unit the supplier quotes, with each item listed and the depth conversion done for you.

    Open Cubic Yards & Volume Calculator
  • Estimate

    Cut & Fill Volume (Grid)

    Earthwork cut and fill by the grid method: paste existing and proposed levels, set the spacing, get cut, fill, net balance and a per-cell table.

    You get: Cut and fill volumes, the net import or export, loose cut and bank fill after your factors, the site area, maximum depths, and a per-cell CSV.

    Open Cut & Fill Volume (Grid)
  • Estimate

    Dumpster Size Calculator

    Debris typed line by line becomes a loose volume, the container size it needs, and — with a bulk density — the weight against the tonnage allowance.

    You get: Measured and loose volume after your bulking factor, the container size at your fill efficiency, how many of the size you have in mind, and the weight with any overweight charge.

    Open Dumpster Size Calculator
  • Calculate

    Excavation & Trench Volume Calculator

    Bank volume of trenches and pits with vertical or sloped sides, loose volume from your swell factor, truck loads from your body capacity, and backfill.

    You get: How much soil comes out, how much bigger it gets on the truck, how many loads that is, and how much goes back — from the trench section and the factors you supply.

    Open Excavation & Trench Volume Calculator
  • Calculate

    Setting Out (3-4-5 & Diagonals)

    Square up a layout: the exact diagonal of a rectangle, the error and corner angle from measured diagonals, and a 3-4-5 triangle scaled to your tape.

    You get: Diagonal to measure, the difference of two measured diagonals with the corner angle and offset it implies, and a 3-4-5 triple sized to a leg you choose.

    Open Setting Out (3-4-5 & Diagonals)
  • Convert

    Slope, Grade & Percent Calculator

    Convert any incline between rise-over-run, percent grade, degrees, 1:x ratio and per-mille, with the rise and slope length over a distance you choose.

    You get: The same slope in the form the drawing, the level, the drainage spec or the ramp note uses — and how much it climbs over a given distance — with the conversions made explicit.

    Open Slope, Grade & Percent Calculator

Landscape & garden8

  • Calculate

    Fertilizer Rate Calculator

    Product needed for an area from the label analysis (N-P-K) and your target nutrient rate, with what each nutrient delivers, split applications and bags.

    You get: Product per 100 m² or 1000 ft² and for the whole area, the N, P₂O₅ and K₂O delivered, applications under a per-application cap and bag count — rate yours, not suggested.

    Open Fertilizer Rate Calculator
  • Estimate

    Grass Seed Calculator

    Seed for a lawn from rectangles, circles or areas typed one per line and the rate on your bag (lb per 1 000 sq ft or kg per 100 m²), with waste, bags and cost.

    You get: Total area, pounds or kilograms of seed with the waste allowance, bags rounded up and their coverage, cost, fertiliser at your rate and the cubic yards or m³ of top-dressing for the depth you set.

    Open Grass Seed Calculator
  • Calculate

    Irrigation Run Time Calculator

    Minutes to apply a depth of water from a zone’s precipitation rate — from flow and area or a catch-cup test — at your efficiency, with cycle-and-soak splits.

    You get: How long to run each sprinkler or drip zone to put down the water depth you decide on, with the precipitation rate shown so the controller can be set with a reason.

    Open Irrigation Run Time Calculator
  • Calculate

    Mulch & Soil Calculator

    Mulch, topsoil or compost for one or more beds at the depth you choose: cubic feet or litres, bulk yards or metres, whole bags from your bag size, and cost.

    You get: How many bags or how many yards to order, with the bag-versus-bulk comparison priced from your own figures and every bed listed.

    Open Mulch & Soil Calculator
  • Estimate

    Plant Spacing Calculator

    How many plants fit a bed or an acre at your spacing, in rows or a triangular offset layout, with plants per acre and hectare, in feet or metres.

    You get: The space each plant takes, how many plants the bed holds, and plants per acre and per hectare, for a grid of rows or an offset triangular layout at the spacing you choose.

    Open Plant Spacing Calculator
  • Calculate

    Pond Liner Size

    Flexible pond liner size from the pond length, width, maximum depth and edge overlap — liner sheet dimensions, area, weight, water volume and roll strips.

    You get: Liner length and width, liner and underlay area, the water volume in m³, litres and US gallons for your shape factor, liner weight from your per-area figure, and strips of a roll width.

    Open Pond Liner Size
  • Calculate

    Rainwater Harvesting Calculator

    Litres or gallons a roof collects from its plan area, a rainfall depth and your runoff coefficient, less first flush, with a monthly table and tank check.

    You get: The yield a catchment gives per rain event, per month and per year, and how many days it covers a demand — from your rainfall records and your roof, with the coefficient stated.

    Open Rainwater Harvesting Calculator
  • Calculate

    Raised Bed Soil Calculator

    Fill volume for one or more raised beds, split into topsoil, compost and amendments by the parts you choose, with whole bags per component from your bag sizes.

    You get: How much of each ingredient to buy for the beds — in bags and in bulk — from your own mix recipe rather than a fixed one.

    Open Raised Bed Soil Calculator

Plumbing & drainage3

  • Calculate

    French Drain Materials

    Trench, stone, fabric and pipe quantities for a French drain, with the fall along the run and the flow the perforated pipe can carry at that slope.

    You get: Excavation and stone volume with waste, tonnes and truck loads or bags at your density, filter fabric area including the overlap, pipe length, the fall at your slope, and the pipe capacity by Manning.

    Open French Drain Materials
  • Calculate

    Gutter & Downspout Sizing

    Roof area and design rainfall give the runoff flow, then the gutter capacity by Manning and the downspout capacity are checked against it.

    You get: Runoff in litres per second and US gallons per minute, the gutter and downspout capacity beside it, how heavily each is loaded, and how many downspouts the flow actually needs.

    Open Gutter & Downspout Sizing
  • Calculate

    Pipe Volume Calculator

    Water or any liquid in a pipe from inside diameter (or OD and wall) and length: litres, gallons, ft³, mass at your density, per metre and per foot, or segments.

    You get: Internal volume in L, m³, US and imperial gallons and ft³, the mass of the liquid at the density you set, volume per metre and per foot, cross-section, and a table for segments typed one per line.

    Open Pipe Volume Calculator

Farm & field4

  • Estimate

    Corn & Soybean Yield Estimate

    Pre-harvest corn and soybean yield by the yield component method: ears or plants in 1/1000 acre, kernels or pods, and your kernel factor or seeds per lb.

    You get: Estimated bushels per acre and tonnes per hectare, the ears or plants per acre your count implies, kernels per ear or seeds per plant, and the row length that makes 1/1000 of an acre at your row width.

    Open Corn & Soybean Yield Estimate
  • Estimate

    Grain Bin Capacity

    Bushels in a round grain bin from its diameter and grain height, with a peaked top at your angle of repose and a hopper bottom, and tons at your test weight.

    You get: The bin’s grain volume in cubic feet and metres, bushels, the peak and hopper shares, and tons and tonnes at the test weight you enter — geometry you can check against the bin’s rating.

    Open Grain Bin Capacity
  • Estimate

    Hay Needs for Livestock

    Hay a herd needs over a feeding period from head, body weight, daily dry-matter intake, the hay’s dry matter and waste — in tons or tonnes and bales.

    You get: The dry matter the herd eats, the hay to buy as fed with waste included in tons or tonnes, the number of bales at your bale weight, and the daily amount per animal.

    Open Hay Needs for Livestock
  • Calculate

    Sprayer Calibration

    Boom sprayer rate from nozzle output, speed and spacing, or the output a label rate needs, in GPA or L/ha, with speed from a timed run and area per tank.

    You get: The application rate your measured nozzles give, or the output each nozzle needs for the label’s rate, the ground speed from a timed run, the whole boom’s flow, and the area one tank covers.

    Open Sprayer Calibration